Monday, February 11, 2013

Beginning of the End, and a New Beginning.

Last train on the Thomas Sub crosses the Cumberland Narrows at Hinshaw.

Starting on Saturday, February 9, I began the process of dismantling the Western Maryland Western lines N scale layout.  I spent a few hours running two extras to clear all the rolling stock from the outer reaches of the railroad.  The first was a move up to Elkins Yard, where a couple of dozen hoppers were left.  These would be brought down the hill in two sections, with stops in Thomas and Luke to clear a few cars from those locations as well.
GP35 3580 ties up to a cut of hoppers in the first section of the last train from Elkins to Ridgeley.


The first section waits for a clear signal at Kerens.  Once clear, the train heads into the helix down to the main level.


First section arrives at Thomas, where another cut of cars will be added for the trip to Ridgeley.
Switching Thomas required venturing out on the high bridge.

Blocking together the last section at Thomas.
Heading down the mountain for the last time.
Across the high bridge then on to Shaw Siding
The view from Shaw looking west along the Thomas Sub toward the high bridge.
Arriving at the TO office at Shaw.  Once the train passes, the operator will pack up the paperwork and drive away for the last time.
Caboose clears Shaw.
Then Maryland Junction, after retrieving a flat car from the paper mill.
Crossing Wills Creek on the steel bridge, which will eventually be installed on a traveling module.
Arriving at Cumberland Station.
The concrete overpass at Greenwood.
And finally to the yard.
A short time later, the final train from Connellsville appeared on the "new" line along the Youghiougheny River.  Led by Laurel Valley locomotives 1803 and 1802.

Emerging from the east portal of Pinkerton Tunnel
Passing under the high bridge
At Thomas Road Bridge
The iconic bridge at Casselman Crossing, subject of at least one N Scale magazine article.
Casselman Crossing
Approaching Maryland Junction along the Potomac
Heading through Cumberland on the way to Ridgeley Yard
Arriving at Ridgeley.  All the rolling stock that remains is now in the yard.
The final work on Saturday was to remove the bridges, including Casselman Crossing, to pack them up for their new owner.
On Sunday, 2/10, the crew came down to Cambridge to help cut out the peninsula and move it to its new home in the Baltimore area.

Here's how it went down...  We got started around 10:30 a.m.  We dismantled North Junction to make room in the doorway, then the cutting began...

Before the move, Ed inspects the cuts, and verifies that all of the electrical connections were severed.


While I was hacking away at foam and sculptamold, Ed and Tim worked on boxing up the remaining rolling stock on the layout.  The last car to officially turn a wheel on the railroad was a B&O bay window caboose of no fixed prototype.

Work on detaching the several layers of track and wiring went on for about an hour.

Brian (Rock GP40) showed up around 11, then we went to lunch to power up before attempting to move the behemoth down the steps.  Plaza Tapatia was the weapon of choice, with ammunition provided by a couple of 32 oz Dos Equis Grandes.

There were no photos taken of the actual move.  It was all hands on deck.  We got it out of the room easily enough, and then turned it over to slide it down the steps, but the 64" wide bulbous end (Andy calls this the "Scrotum") simply wouldn't make it through the opening.  We had to heft it back up the steps twice to trim portions off.  Finally we removed the high bridge and the entire subroadbed that had supported the Shaw siding, and this allowed us to get Elvis out of the building.



We loaded the main section into my girlfriend's pick up, and all the remaining bits and pieces from the surgery into the cab, and headed across the great waters of the Chesapeake toward Eric's house near the airport.

Once at Eric's, we found the path to the basement to be relatively straight, but not without challenges.  We had to move the picnic table over to the steps from the car port so we could gain enough height to heft it over the railing and into the house.  We had to remove both the exterior door and basement door from their hinges to provide enough clearance.  Again, there wasn't a stray set of hands to work the camera, so you'll have to take the word of the witnesses.

With only inches to spare, it fit over the railing, under the carport ceiling, through the two doors, and down the steps.  Due to bad planning, Eric ended up at the bottom of the steps by himself as the full brunt of the peninsula went down the stairway.  Imagine standing out in center field by yourself trying to field a fly ball that happens to be as big as a submarine.

Anyway, we recovered, got it down the narrow aisle next to Sunnyside, and spun into position at rest on a temporary table.


The next challenge for Eric and the crew is to work out the elevation changes of the peninsula and marry them to the existing shelf layout along the wall in the background.

I appreciate the hard work and ingenuity that went into this move, and I'm now anxious to get the rest of the layout moved along to be stored or incorporated into another layout or three.  I also appreciate Eric generously offering to make a home for this favorite piece of work.  I'm looking forward to helping to tie in the scenery, and to running some Laurel Valley power up the Yough Valley once again.



Lee

3 comments:

  1. It's sad to see that the modelled WM has now become a Fallen Flag, like its namesake.

    You mention that Eric is going to merge part of the layout into his own layout. How much of the layout have you found a new home for?

    Best wishes,
    Ron McF

    ReplyDelete
    Replies
    1. I've got temporary quarters for the remaining portable sections, but no permanent homes. It will be a while before I have a space I can call my own, but we'll see...

      Delete
    2. Last year the Ridgeley Yard section of the WM was parceled out to Ed Kapuscinski. You can read more about that in his Conrail Windsor Street Yard thread on www.therailwire.net

      Delete